Open Location Code for Swift

Convert between decimal degree coordinates and Open Location Codes. Shorten and recover Open Location Codes for a given reference location.

This repository is the Swift implementation of Open Location Code. It supports Swift and Objective-C projects on iOS, macOS, tvOS and watchOS, and Swift projects on Linux. The master repository has Open Location Code support for many other languages.

Open Location Codes are short, 10-11 character codes that can be used instead of street addresses. The codes can be generated and decoded offline, and use a reduced character set that minimises the chance of codes including words.

Codes are able to be shortened relative to a nearby location. This means that in many cases, only four to seven characters of the code are needed. To recover the original code, the same location is not required, as long as a nearby location is provided.

Codes represent rectangular areas rather than points, and the longer the code, the smaller the area. A 10 character code represents a 13.5x13.5 meter area (at the equator. An 11 character code represents approximately a 2.8x3.5 meter area.

Two encoding algorithms are used. The first 10 characters are pairs of characters, one for latitude and one for latitude, using base 20. Each pair reduces the area of the code by a factor of 400. Only even code lengths are sensible, since an odd-numbered length would have sides in a ratio of 20:1. At position 11, the algorithm changes so that each character selects one position from a 4x5 grid. This allows single-character refinements.

This library is provided as a Swift and Objective-C Cocoa Framework for iOS, macOS, tvOS and watchOS, and as a pure Swift module for macOS and Linux.

• Versions 1.x of Open Location Code for Swift are designed for Swift 3.2.
• Versions 2.x of Open Location Code for Swift are designed for Swift 4.0.

Choose the latest 1.x release for greater compatability, or the latest 2.x release if you're fully in the Swift 4 world!

To build the Framework:

xcodebuild -project OpenLocationCode.xcodeproj -scheme OpenLocationCode_iOS -configuration Release
xcodebuild -project OpenLocationCode.xcodeproj -scheme OpenLocationCode_macOS -configuration Release
xcodebuild -project OpenLocationCode.xcodeproj -scheme OpenLocationCode_tvOS -configuration Release
xcodebuild -project OpenLocationCode.xcodeproj -scheme OpenLocationCode_watchOS -configuration Release

Or, if you have Carthage installed:

carthage build --no-skip-current

Testing the framework:

xcodebuild test -project OpenLocationCode.xcodeproj -scheme OpenLocationCode_macOS -destination 'platform=OS X,arch=x86_64'

To build the pure Swift module:

swift build

Testing the pure Swift module:

swift test

A Dockerfile is included to build and run the pure Swift module in a Linux container:

docker build .

import OpenLocationCode

// Encode a location with default code length.
if let code = OpenLocationCode.encode(latitude: 37.421908,
                                      longitude: -122.084681) {
  print("Open Location Code: \(code)")
}

// Encode a location with specific code length.
if let code10Digit = OpenLocationCode.encode(latitude: 37.421908,
                                             longitude: -122.084681,
                                             codeLength: 10) {
  print("Open Location Code: \(code10Digit)")
}

// Decode a full code:
if let coord = OpenLocationCode.decode("849VCWC8+Q48") {
  print("Center is \(coord.latitudeCenter), \(coord.longitudeCenter)")
}

// Attempt to trim the first characters from a code:
if let shortCode = OpenLocationCode.shorten(code: "849VCWC8+Q48",
                                            latitude: 37.4,
                                            longitude: -122.0) {
  print("Short code: \(shortCode)")
}

// Recover the full code from a short code:
if let fullCode = OpenLocationCode.recoverNearest(shortcode: "CWC8+Q48",
                                                  referenceLatitude: 37.4,
                                                  referenceLongitude: -122.0) {
  print("Recovered full code: \(fullCode)")
}

@import OpenLocationCode;

// ...

// Encode a location with default code length.
NSString *code = [OLCConverter encodeLatitude:37.421908
                                    longitude:-122.084681];
NSLog(@"Open Location Code: %@", code);

// Encode a location with specific code length.
NSString *code10Digit = [OLCConverter encodeLatitude:37.421908
                                           longitude:-122.084681
                                          codeLength:10];
NSLog(@"Open Location Code: %@", code10Digit);

// Decode a full code:
OLCArea *coord = [OLCConverter decode:@"849VCWC8+Q48"];
NSLog(@"Center is %.6f, %.6f", coord.latitudeCenter, coord.longitudeCenter);

// Attempt to trim the first characters from a code:
NSString *shortCode = [OLCConverter shortenCode:@"849VCWC8+Q48"
                                       latitude:37.4
                                      longitude:-122.0];
NSLog(@"Short Code: %@", shortCode);

// Recover the full code from a short code:
NSString *recoveredCode = [OLCConverter recoverNearestWithShortcode:@"CWC8+Q48"
                                                  referenceLatitude:37.4
                                                 referenceLongitude:-122.1];
NSLog(@"Recovered Full Code: %@", recoveredCode);